收藏本站
Not Recommended for New Designs
Application Information (continued)
OVP – Overvoltage Protection
The output Overvoltage Protection set point of the P045F048T17AL is
factory preset for 56 V. If this threshold is exceeded the output shuts
down and a restart sequence is initiated, also indicated by PC pulsing.
If the condition that causes OVP is still present, the unit will again shut
down. This cycle will be repeated until the fault condition is removed.
V?I Chip Regulator
Adjusting Current Limit
The current limit can be lowered by placing an external resistor
between the I L and SG ports (see Figure 18 for resistor values) . With
the I L port open-circuit, the current limit is preset to be within the
range specified in the output specifications table on Page 4.
The OVP set point may be set at the factory to meet unique high
voltage requirements.
PRM Output Power Versus VTM Output Power
As shown in Figure 17, the P045F048T17AL is rated to deliver 3.5 A
maximum, when it is delivering an output voltage in the range from
26 V to 48 V, and 170 W, maximum, when delivering an output
voltage in the range from 48 V to 55 V. When configuring a PRM for
use with a specific VTM, refer to the appropriate VTM data sheet. The
VTM input power can be calculated by dividing the VTM output power
by the VTM efficiency (available from the VTM data sheet). The input
1000
100
10
Current Limit Set Resistors
Current (A)
power required by the VTM should not exceed the output power
rating of the PRM.
1
0.5
1
1.5
2 2.5
3
3.5
4
4.5
3.6
3.5
3.4
3.3
Figure 18 — Calculated external resistor value for adjusting current limit,
actual value may vary.
3.2
3.1
3.0
2.9
2.8
0
~ ~
Safe Operating Area
Input Fuse Recommendations
A fuse should be incorporated at the input to the PRM, in series with
the +IN port. A fast acting fuse, NANO2 FUSE 451/453 Series 10 A
125 V, or equivalent, may be required to meet certain safety agency
Conditions of Acceptability. Always ascertain and observe the safety,
regulatory, or other agency specifications that apply to your specific
application.
20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60
Factorized Bus Voltage (V f )
Product Safety Considerations
Figure 17 — P045F048T17AL rating based on Factorized Bus voltage
If the input of the PRM is connected to SELV or ELV circuits, the output
of the PRM can be considered SELV or ELV respectively.
The Factorized Bus voltage should not exceed an absolute limit of
55 V, including steady state, ripple and transient conditions. Exceeding
this limit may cause the internal OVP set point to be exceeded.
Parallel Considerations
The PR port is used to connect two PRMs in parallel to form a higher
power array. When configuring arrays, PR port interconnection
terminating impedance is 10 k to SG. See note Page 8 and refer to
Application Note AN002. Additionally one PRM should be designated
as the master while all other PRMs are set as slaves by shorting their
SC pin to SG. The PC pins must be directly connected (no diodes) to
assure a uniform start up sequence. Consult Vicor applications
engineering for applications requiring more than two PRMs.
Applications Assistance
Please contact Vicor Applications Engineering for assistance,
1-800-927-9474, or email at apps@vicr.com.
vicorpower.com
800-735-6200
V?I Chip Regulator
P045F048T17AL
Rev. 2.6
Page 10 of 14
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
P045T048T32AL V.I CHIP PRM REGULATOR 48V 320W
P048T048M24AL V.I CHIP PRM REGULATOR 48V 240W
P048T048T12AL V.I CHIP PRM REGULATOR 48V 120W
P081N-271F2CBR10K POT MODULE 8MM 10K SIDE ADJ
P090L-02T20BR50K POT ROTARY 50K OHM 9MM SNAPIN
P092N-QC15AR20K POT ROTARY 20K OHM 9MM
P110KH1-0F25BR10K POT ROTARY 10K OHM 11MM BUSHING
P120K-F20BR5K POT ROTARY 5K OHM 12MM SGL INS
相关代理商/技术参数
P045T048T32AL 功能描述:V.I CHIP PRM REGULATOR 48V 320W RoHS:是 类别:电源 - 板载 >> DC DC 转换器（分解式） 系列:V-I Chip™, PRM™ 应用说明:Factorized Power Architecture and V-I Chips 产品培训模块:VI Chip Bus Converter Modules 标准包装:1 系列:V-I Chip™, BCM™ 类型:总线转换器模块 输出数:1 电压 - 输入（最小）:330V 电压 - 输入（最大）:365V 输出电压:12.5V 电流 - 输出（最大）:24A 电源（瓦） - 制造商系列:300W 电压 - 隔离:4.242kV（4242V） 应用:商用 特点:具有远程开/关功能和 UVLO 安装类型:通孔 封装/外壳:模块 尺寸/尺寸:1.28" L x 0.87" W x 0.26" H（32.5mm x 22.0mm x 6.7mm） 包装:托盘 工作温度:-55°C ~ 125°C 效率:95.3% 电源（瓦特）- 最大:300W 重量:0.031 磅（14.06g）
P0460 制造商:Pulse Electronics Corporation 功能描述:Inductor Power Shielded Wirewound 34uH 15% 1A 104mOhm DCR 制造商:Pulse Electronics Corporation 功能描述:Ind Power Shielded Wirewound 34uH 15% 1A
P046-06N 制造商:Tripp Lite 功能描述:12AWG HVY DTY PWR ADPTR 100-250V 制造商:Tripp Lite 功能描述:6IN 12AWG HVY DTY POWER ADPTR CORD 100-250V 20A L5-20P TO 5- - Bulk
P0460NLT 功能描述:固定电感器 ROS 2, 22.95uH 1A 5.3mm Max Ht. RoHS:否 制造商:AVX 电感:10 uH 容差:20 % 最大直流电流:1 A 最大直流电阻:0.075 Ohms 工作温度范围:- 40 C to + 85 C 自谐振频率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接类型:SMD/SMT 封装 / 箱体:6.6 mm x 4.45 mm
P0460T 功能描述:固定电感器 22.95uH 1A 5.3mm Max Ht. RoHS:否 制造商:AVX 电感:10 uH 容差:20 % 最大直流电流:1 A 最大直流电阻:0.075 Ohms 工作温度范围:- 40 C to + 85 C 自谐振频率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接类型:SMD/SMT 封装 / 箱体:6.6 mm x 4.45 mm
P0461059402 制造商:LG Corporation 功能描述:KNOB ARRAY
P046-10594-02 制造商:LG Corporation 功能描述:KNOB ARRAY PUSH BUTTON
P0461059602 制造商:LG Corporation 功能描述:KNOB ARRAY